WATERS 48 Position and 717
|
|
|
The standard vial for this autosampler is the 4mL screw top,
15 x 45mm vial i.e. 4-SV. This is also available in amber
glass, 4-SV(A). Using our extensive range of PTFE sleeves
many of our micro vials may be used with these autosamplers.
|
|
|
| Table
1 |
VIALS
USING 12mm
SCREW CAPS |
| 1 |
4-SV
|
4mL,
clear glass, screw top, flat bottom vial. |
| 2 |
4-SV(A)
|
4mL,
amber glass, screw top, flat bottom vial. |
| |
RECOMMENDED
CAPS |
| |
12-SC
|
Screw
cap, black, no seal. Also available in green, red, white and
yellow. |
| |
12-SC-8RT1 |
Screw
cap, black, pre-fitted with a 1mm thick, type 8, rubber/PTFE
seal. |
| |
12-SC-ST2 |
Screw
cap, black, pre-fitted with a 2mm thick, silicone/PTFE seal.
|
| |
RECOMMENDED
SEALS |
| |
12-ST2 |
White
silicone/red PTFE seal. Shore hardness value 57. |
| |
12-ST18 |
Blue
silicone/PTFE seal. |
| |
12-T02 |
White
PTFE seal. Does not re-seal. |
|
| Table
2 |
VIALS USING
11mm CRIMP CAPS
|
| |
4-CV |
4mL,
clear glass, crimp top, flat bottom vial. |
| |
2-CV
|
2mL,
clear glass, wide neck, crimp top, flat bottom vial. With 'write-on'
patch. |
| |
2-CVG |
2mL,
clear glass, wide neck, crimp top, flat bottom vial made from
inert Chromacol GOLD™
grade glass. |
| |
2-CV(A)
|
2mL,
amber glass, wide neck, crimp top, flat bottom vial. With 'write-on'
patch. |
| |
1.1-CTVG |
1.1mL,
clear glass, crimp top, tapered vial made from inert CHROMACOL
GOLD™
grade glass. Needs a TTS-312 PTFE support sleeve and a WS-2. |
| |
03-FIV
|
300無,
one piece, clear glass insert and vial combination. With 'write-on'
patch. Micro+™.
|
| |
03-FIV(A) |
300無,
one piece, amber glass insert and vial combination. With 'write-on'
patch. Micro+™.
All the above vials (except 1.1-CTVG) need to be used with a
WS-7 PTFE support. |
| |
RECOMMENDED
11mm CRIMP (Silver) CAPS |
| |
11-ACT |
Aluminium
crimp cap fitted with a plain PTFE disc seal. Does not re-seal.
|
| |
11-AC-ST15 |
Aluminium
crimp cap fitted with a white silicone/red PTFE seal. Shore
hardness value 57. |
| |
11-AC5 |
Aluminium
crimp cap fitted with a type 5, rubber/PTFE seal. Shore hardness
value 38. Available in other colours. |
|
| Table
3 |
MICRO-VIALS
USING 8MM CRIMP CAPS |
| |
03-CVG |
300無,
clear glass, crimp top, round bottom vial, made from inert CHROMACOL
GOLD™
grade glass. Needs support sleeves, either SV-S11A + WS-2 or
SV-S15 |
| |
02-CTVG |
200無,
clear glass, crimp top, tapered vial, made from inert CHROMACOL
GOLD™
grade glass. Needs support sleeves, either SV-S11A + WS-2 or
SV-S15 |
| |
01-CVG |
100無,
clear glass, crimp top, round bottom vial, wit needle guide,
made from inert CHROMACOL GOLD™
grade glass, with built in needle guide. Needs support sleeves,
either SV-S11A + WS-2 or SV-S15 |
| |
RECOMMENDED
8mm CRIMP (Silver) CAPS |
| |
8-AC5 |
Aluminium
crimp cap fitted with a type 5, rubber/PTFE seal. Shore hardness
value 38. |
| |
8-AC-ST15 |
Aluminium
crimp cap fitted with a white silicone/red PTFE seal. Shore
hardness value 57. |
|
| Note |
Our SCI-V™
SYSTEM vials, including the new 01-CVG vial, may be used as
reduced volume inserts in a 4-SV vial with an S-50 spring. 07-CPV(A)
vial can be used as a reduced volume amber insert with an S-15
spring. Our preferred solution is the new SV-S15, a new one
piece low cost plastic support which replaces the above mentioned
4mL vial. This easy and simple to use support uses any one of
the SCI-V™
System vials, i.e. 03-CVG, 02-CTVG and the 01-CVG. |
|
|
|
|